IRSIM SIMULATOR FREE DOWNLOAD

Using the trace command, it is possible to get more detail about what's happening to a particular node. Removes nodes from whatever input list they happen to be on. Usually this command will be followed by an isim command see below , if that is not the case then it's up to the user to initilize the state of the circuit. If a node keeps appearing in this prinout, chances are that its value is oscillating. Like " h " except forces nodes to be a low 0 input. The default resolution is 0 ns. A value of 0 implies no decay at all.

Uploader:	Vusar
Date Added:	9 May 2018
File Size:	27.66 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	33674
Price:	Free* [*Free Regsitration Required]

Depending on the debug level see the " debug " command each calculation of a traced node's value is reported: After all the command files have been processed, and if an "exit" command has not terminated the simulation run, IRSIM will accept further commands from the user, prompting for each one like so: With no arguments powlogfile just closes the opened logfile and prints out a power dissipation summary.

Usually this command will be followed by an isim command see belowif that is not the case irsi, it's up to the user to initilize the state of the circuit. simulxtor

Ubuntu Manpage: irsim - An event-driven logic-level simulator for MOS circuits

Any node simulatpr be set using the h, l, u or set commands. With no arguments, each of the commands simply prints the current value of the parameter.

A simulation step continues until stepsize ns. A similar mechanism is used to define the sequence of values each clock node goes through during a single cycle. If the comparison fails, an error message is printed.

Useful for keeping user posted of progress through a long command file. Although transistors connected across the power supplies are real design errors, the simulator does not complain about them. The default resolution is 0 ns. There is only a single name space for nodes, so references to node "A" in different network files all refer to the same node.

simulayor If n is specified, it will temporarily override the stepsize value. If display mode is automatic see " display " command the display is printed at the end of each cycle. If this is the case you can use the Xdisplay command to set it from within the simulator. To simulate the device for all possible input combinationsrepeat the described steps, while setting different values for the input nodes.

IRSIM 9.7 Reference

This is the default state of most nodes. Wild cards are not accepted in the list of node names since you would have no control over the order in which matching nodes would appear in the vector. Succeeding lines list the transistor whose sources or drains connect to si,ulator node: Without any arguments, the debug command prints the current debug level.

The format of the report is the same you get when you trace a node normaly. Delays may not reflect the true speed of the circuit as well. Removes nodes from whatever input list they happen to be on. While this feature allows one to modularize a large circuit into several network files, care must be taken to ensure that no unwanted node merges happen due to an unfortunate clash in names.

Simply prints the text on the user's console. With no arguments, the name of the current X-server will be printed. During resimulation, a node is considered to deviate from its history if it's new state is found to be different within n ns of its previous state.

irsim (1) - Linux Man Pages

This command will restore the state of the circuit to that of the dump file, overwriting the current state. Each " R " command starts over at the beginning of the sequence defined for each node. Prefacing the node name with '-' clear its trace flag.

With no arguments, it will print the current resolution. Blanks spaces and tabs are used to separate values in a sequence. If a mask is specified, then bits that were not compared are printed as '-'.

After input values have been established, their simulwtor can be propagated through the network with the following commands. If a debug switch is on then during a simulation step, each time a watched node is encounted in some event, that fact is indicated to the user along with some event info.